Skip to Main Content
SearchClear
KITS, Torque

Torque Sensor (100 N·m to 1000 N·m)

The intent of the TORQ-SENSOR-1224 is to provide a means for participant labs to evaluate the appropriateness and effectiveness of participant practices, training, and measurement uncertainty relating to calibration of a Torque Sensor.

The kit includes Moorhouse Torque PT and C705P Load Cell. Participants are asked to make 10 measurements of Torque from 100 N·m to 1000 N·m. The most common method used for this ILC/PT will consist of tests weights and torque arm.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in Kit: Morehouse Torque PT, C705P Load Cell

Show Details Inquire
KITS, Torque

Torque Screwdriver Set

The intent of this ILC/PT is to give organizations an opportunity to evaluate their proficiency (e.g., use of appropriate equipment, procedures, ability to follow instructions) in the calibration of a Torque Screwdriver Set.

By participating, participants will demonstrate technical competence for the measurement of parameters associated with like equipment. The kit consists of four torque screwdrivers. Range of measurements are 20 ozf·in to 36 lbf·in. 

Participants are expected to be familiar with and have appropriate lab equipment and measurement uncertainties for the calibration of similar devices.

Artifact in kit: Sturtevant Richmont, 810064 & CAL-36/4 & 810007

torque screwdriver set

Show Details Inquire
KITS, Torque

Torque Wrench Set

The primary purpose of this ILC/PT is to determine the appropriateness and effectiveness of the participant’s methods, procedures, training, and measurement uncertainty calculations relating to the measurement of torque by comparison of reported data and uncertainties to the data and uncertainties of other laboratories measuring the same data points on the same artifacts. 

This ILC/PT Kit contains three wrenches for a total of 9 measured value (MV) points.  Ranges of each wrench is as follows: M100 1/2 - 20 to 100 ft. lbf, 2SDR 150I MG - 30 to 150 in lb, and the 3sdr 750i - 150 to 750 in lb. 

Participants are asked to use their lab practices to make Torque measurements.  Measurement values will be appropriate for calibration of similar devices. 

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Torque

Torque Wrench Set

The primary purpose of this ILC/PT is to determine the appropriateness and effectiveness of the participant’s methods, procedures, training, and measurement uncertainty calculations relating to the measurement of torque by comparison of reported data and uncertainties to the data and uncertainties of other laboratories measuring the same measured values on the same UUT. 

This ILC/PT contains 2 torque wrenches: one digital 1800 in*lb and one flat beam 600 in*lb.  

Participants are asked to use their lab practices to make torque measurements at three measured values per wrench for a total of six measured values in the range of 100 to 1800 in*lb.  Measurement values will be appropriate for calibration of similar devices.

Show Details Inquire
Torque

Torque Wrench Kit

The intent of this ILC/PT is to provide a means for participant laboratories to evaluate the appropriateness and effectiveness of the their practices, training, and measurement uncertainties relating to the measurement of Torque by comparison of reported data and uncertainties to the data and uncertainties of other laboratories measuring the same data points on the same artifacts.  

This ILC/PT Kit contains 2 Torque Wrenches: One Digital 1800 lbf·in and one Flat Beam 600 lbf·in Wrenches.

Participants are asked to use their lab practices to make Torque measurements at three Set Points per wrench for a total of 6 Set Points in the range of 100 to 1800 lbf·in. Measurement values will be appropriate for calibration of similar devices. 

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Torque

Torque Wrench Set of 4 Wrenches

The intent of this ILC/PT is to provide a means for participant laboratories to evaluate the appropriateness and effectiveness of the their practices, training, and measurement uncertainties relating to the measurement of Torque by comparison of reported data and uncertainties to the data and uncertainties of other laboratories measuring the same data points on the same artifacts.

This ILC/PT Kit contains 4 Torque Wrenches: two Digital 1800 in*lb and 2 Flat Beam 600 in*lb Wrenches.

Participants are asked to use their lab practices to make Torque measurements at three Set Points per wrench for a total of 12 Set Points in the range of 100 to 1800 in*lb. Measurement values will be appropriate for calibration of similar devices. 

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Torque

Torque Transducer

This program is offered to laboratories simulating torque measurements with transducers or the combination of weights and arms.

Participants measure torque in the clockwise (CW) and counter-clockwise (CCW) direction from 200 lbf*in to 2000 lbf*in. The results are provided in mV/V with the reported uncertainty. The associated uncertainty for this program is in the range of 0.002 mV/V to 0.004 mV/V.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: TLB, Reaction Torque Transducer

torque transducer

Show Details Inquire
KITS, Torque

Torque Wrench Set of 3 Wrenches

The intent of this ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of participant practices, training, and measurement uncertainty relating to calibration of Torque Wrenches with a reference uncertainty of 2% i.v. on pound*inch range and 1% i.v. on pound*foot range.  

This ILC/PT Kit contains three Torque Wrenches, covering ranges 30 in*lb to 540 in*lb and 20 ft*lb to 90 ft*lb. Participants are asked to use their lab practices to make measurements of Torque at nine set points (three set points per wrench). Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire

Theme picker

Copyright 2024 National Association for Proficiency Testing (NAPT)

Website developed by 10 Pound Gorilla

Contact Us Privacy & Terms