Equipment & Tools for Sale

This is a four terminal device requires current from 2µA to 10µA. Participants are requested to make 4 predetermined measurements from 0 °C to 100 °C with five inch immersion. Best Measurement Capability of participant should not be greater than the accuracy of the UUT. Uncertainties expected will range from 0.017 °C to 0.13 °C.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: Fluke, 5610-9

The intent of the Temp-IR-114 is to provide a means for the participant lab to determine the appropriateness and effectiveness of practices, training, and measurement uncertainty relating to the ability of the lab to generate and measure infrared temperatures using a calibrated infrared thermometer. The participant infrared standard will be used as a source for all measurements.

This ILC/PT Kit contains an IR Thermometer with 0.1 °C resolution and 1% / 1 °C (whichever is greater) accuracy spec. Participants are asked to use their lab practices to make 8 measurements of temperature between -20 °C and 750 °C.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: Fluke-68-IS

This ILC/PT Kit contains a Digital Thermometer with Probe. Participants are asked to use their lab practices to make 4 measurements of temperature from -20 °C to 120 °C. UUT resolution is 0.01 °C. UUT manufacturer accuracy spec is +/- 0.012 °C. 

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

The temperature range is from 0 °C to 990 °C with expected measurement uncertainties from 0.25 °C to 1.0 °C. The 4 mA to 20 mA output is also calibrated with uncertainties in the 0.01 mA to 0.02 mA range.

Participants are asked to simulate input values and measure output current from the controller.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

This ILC/PT Kit contains a Digital TC Calibrator. Resolution for TC Source: 0.1°C; Measure: 0.01 °C.  Accuracy at set points is 0.2 °C to 1.2 °C depending on TC type. TC types available for both Source and Measure include J, K, T, E, R, S, B, L, U, & C. Participants are asked to use their lab practices to perform 20 set point measurements of TC Source (x10) and Measure (x10). 

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Participants are requested to make eleven measurements from -196 to 410 C. The probe should be immersed to a minimum depth of 4".

The pivot lab uncertainty ranges from 7.2 mK to 18 mK.

Participants are expected to be familiar with this device and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: Fluke, 5615 (1/4" diameter probe)

No other means of humidity generation is allowed for this ILC, i.e. salt solutions. If your organization does not simulate humidity via this method you are instructed not to participant in this ILC. NAPT has designed additional Humidity ILC/PT's for other methods. Make sure you are participating in the correct ILC/PT for your method of humidity generation. Artifact chosen for this ILC has a range of 0 to 100 %RH. Accuracy of artifact is 1% RH. Initial reference laboratory calibration of test artifact was performed at 23 degrees C. 

This ILC/PT Kit contains a Digital Humidity Indicator with sensor. Participants will use their lab practices to perform 7 measurements of Relative Humidity percent from 10.00 to 90.00 %RH. Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

No other means of humidity generation is allowed for this ILC, i.e. salt solutions. If your organization does not simulate humidity via this method you are instructed not to participant in this ILC. NAPT has designed additional Humidity ILC/PT's for other methods. Make sure you are participating in the correct ILC/PT for your method of humidity generation.

Artifact chosen for this ILC has a range of 0 to 100 %RH. Accuracy of artifact is 1% RH. Initial reference laboratory calibration of test artifact was performed at 21.7 C. calibration of a Humidity Sensor with indicator.

This ILC/PT Kit contains a Digital Humidity Indicator with sensor. Participants will use their lab practices to perform 7 measurements of Relative Humidity percent from 10.00 to 90.00 %RH. Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.