Skip to Main Content
SearchClear
KITS, Dimensional

Thread Plug Gauge Set

The primary purpose of this THTP-5024 is to determine the appropriateness and effectiveness of the participant’s methods, procedures, training, and measurement uncertainty calculations relating to the measurement of thread set plug gauges.  This kit consists of ¼-20 UNC-2A, 10-32 UNF-2A, 3-56 UNF-2A.

Participants are asked to make 12 measurements that focus on the pitch diameter and major diameter (full form) for various thread standards and conditions (GO and NO GO), with values reported in inches and accompanied by measurement uncertainties.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: Set of three (3) GSG, Thread Set Gage, ¼-20 UNC-2A, 10-32 UNF-2A, 3-56 UNF-2A

 

Show Details Inquire
KITS, Dimensional

12" Single Beam Height Gauge

The intent of the HGTG-7024 ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of the participant's practices, training, and measurement uncertainty relating to calibration of an Electronic Height Gauge.

This ILC/PT Kit contains an electronic height gauge with a 0.0005-inch resolution with a stated manufacturer's accuracy of ±0.001 inches. Participants will use their lab practices to perform 12 measurements of height from zero to 12 inches. Measurement values will be appropriate for the calibration of similar devices.

Participants are expected to be familiar with height gauges and must have appropriate lab equipment and measurement uncertainties for the calibration of similar devices.

Artifact in kit: Mitutoyo, Model 570-412, Digimatic Height Gauge 12".

Show Details Inquire
Dimensional

Thread Wires - Set of 9

This ILC/PT provides three sets of thread wires, each containing three wires (wires are typical of those used for 60 degree; TPI 20, 40, and 80 thread gauge calibration). Wires have been identified by size and color.

Participants are asked to measure these nine thread wires following their established procedures and report the results along with associated uncertainty. The reference uncertainty will be in the order of 0.00002 in.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
Dimensional

Thread Plug Gauge Set

The primary purpose of this ILC/PT is to determine the appropriateness and effectiveness of the participant’s methods, procedures, training, and measurement uncertainty calculations relating to the measurement of thread set plug gauges.  This kit consists of a 3/4-20 UNEF 2B; a 2-56 UNC 2B, and a M8 X 1.0-6H set of thread plug gauges.

By participating, participants will demonstrate technical competence for the measurement of parameters associated with Thread Plug Gauges. Associated reported uncertainties will also be evaluated as part of this ILC/PT.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in kit: Set of 3 Vermont Gage Thread Plug Gauges

3/4-20 UNEF 2B

 2-56 UNC 2B,

 M8 X 1.0-6H 

set of three thread plug gauges

Show Details Inquire
Dimensional

Thread Plug Set

The primary purpose of this ILC/PT is to determine the appropriateness and effectiveness of the participant’s methods, procedures, training, and measurement uncertainty calculations relating to the measurement of thread set plug gauges.  This kit consists of a 3/4-10 UNC; a 1/4-20 UNC-2A; a 1 47/64-20 UNS-2B; set of thread plug gauges.

By participating, participants will demonstrate technical competence for the measurement of parameters associated with Thread Plug Gauges. Associated reported uncertainties will also be evaluated as part of this ILC/PT.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
Dimensional

Spline Gauge

This External Spline kit gives organizations an opportunity to demonstrate their proficiency (e.g., use of appropriate equipment, procedures, and ability to follow instructions) in the calibration of an External Spline Gauge.

By participating, participants will demonstrate technical competence for the measurement of parameters associated with measurement over wire, major diameter measurements, and circular tooth thickness as related to a spline gauge.  The associated reported uncertainties of the measurement will also be evaluated as part of this ILC/PT.

Participants are expected to be familiar with and have appropriate lab equipment and measurement uncertainties for the calibration of similar devices.

Artifact in kit: Leader Corp. GO External Spine Gauge, DWG.# 19412A_00

external spline gauge

Show Details Inquire
KITS, Dimensional

Cylindrical Ring Gauge Set

The Ring-4024 is a six-piece ring gauge set provides the laboratory an opportunity to demonstrate technical competence in the measurement of the inside diameter. Sizes vary from 0.5" to 4.0".

Participants are expected to be familiar with and have appropriate lab equipment and measurement uncertainties for the calibration of similar devices.

Artifacts in kit: GSG Class XXX Steel Ring Gauges - 0.5", 1.0", 1.5", 2.0", 3.0", 4.0"

Show Details Inquire
Dimensional

Plain Cylindrical Ring Gauge Set

This six piece ring gauge set provides the laboratory an opportunity to demonstrate technical competence in the measurement of the inside diameter. Sizes vary from 0.5 in to 4.0 in. Reference uncertainties are in the range of 14 µin to 20 µin. Participants have been able to demonstrate uncertainties in the range of 20 µin to 30 µin.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifacts in kit: Ottawa Gage, Steel Ring Gauges - 0.5", 1.0", 1.5", 2.0", 3.0", 4.0"

Show Details Inquire
Dimensional

12 inch Steel Rule

The intent of this ILC/PT is to provide a means for participant labs to evaluate the appropriateness and effectiveness of participant practices, training, and measurement uncertainty relating to calibration of a Steel Rule.

Participants will use their lab practices to perform 20 measurements ranging from 1.00000 to 12.00000 in at the 14th/28th, 16th/32nd/64th, 12th/24th/48th, and 10th/20th/50th/100th Scales. Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in Kit: Starret, No. C601, 12" Steel Rule

twelve inch starret steel rule

**TRAVEL KIT: This kit travels with the R6-120, should you decide to participate in the R6-120 there is an additional $100 fee per ILC/PT.

Show Details Inquire
Dimensional

6 inch Steel Rule

The intent of this ILC/PT is to provide a means for participant labs to evaluate the appropriateness and effectiveness of participant practices, training, and measurement uncertainty relating to calibration of a Steel Rule.

Participants will use their lab practices to perform 20 measurements ranging from 0.50000 to 6.00000 in at the 14th/28th, 16th/32nd/64th, 12th/24th/48th, and 10th/20th/50th/100th Scales. Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Artifact in Kit: Starret, No. C601, 6" Steel Rule

starret six inch steel rule

**TRAVEL KIT: This kit travels with the R12-220, should you decide to participate in the R12-220 there is an additional $100 fee per ILC/PT.

Show Details Inquire
Dimensional

Protractor

The intent of this ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of the participant's practices, training, and measurement uncertainty relating to calibration of a protractor.

Show Details Inquire
KITS, Dimensional

Plain Cylindrical Plug Gauge Set

The intent of this ILC/PT is to provide a means for participant laboratories to determine the appropriateness and effectiveness of participant practices, training, and measurement uncertainty calculations relating to the calibration of Cylindrical Plug Gauges.

This program provides the opportunity to measure the outside diameter of four plugs from one-half inch to three inch. This ILC is beneficial to laboratories with measurement uncertainties in the 23 µin to 40 µin range. The associated reference uncertainty is 18 µin to 24 µin.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Pin Gauge Set

This program consists of the calibration of twelve pin gauges varying in size from 0.0615 inch to 0.2495 inch. The intent of this test is to provide a means for participants to demonstrate competence in the calibration of these or similar devices. The associated uncertainty is in the order of 60 µin.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Micrometer Length Standards

The intent of this ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of participant practices, training, and measurement uncertainty relating to the calibration laboratories competence in the measurement of a set of length standards.

This seven piece set varies from 1 inch to 7 inches, in 1 inch increments. The associated reference uncertainty is on the order of 20 µin to 40 µin. Participants will use their lab practices to perform 7 measurements of length. Measurement values will be appropriate for calibration of similar devices.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Digital Micrometer and Caliper Set

The intent of this ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of participants practices, training, and measurement uncertainty relating to calibration of a micrometer and a caliper.

This ILC-PT includes both a micrometer and caliper in one kit. The one inch micrometer has five readings within its range. The caliper has four readings over the six inch range. Measurement uncertainties reported are in the order of 0.0004 inch.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Digital Micrometer and Caliper Set

The intent of this ILC/PT is to provide a means for the participant to determine the appropriateness and effectiveness of participants practices, training, and measurement uncertainty relating to calibration of a micrometer and a caliper.

This program provides both a micrometer and caliper in one set. The one inch micrometer requires five readings within its range. The caliper requires four readings over the six inch range. Measurement uncertainties reported are in the order of 0.0004 inch.

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Inspection Parts - Pin, Aluminum Cast Artifact

The intent of this ILC/PT is to provide a means for the participant organization to evaluate the ability of a technician to make measurements using dimensional inspection test equipment. For this ILC/PT, micrometers, height gauges and calipers are the only inspection measuring equipment to be used.

This program involves the measurement of distances, locations, and the inside and outside diameters of an aluminum artifact with approximate dimensions 150 mm x 100 mm x 35 mm, and a set of Deltronic pins. Reference values are obtained by CMM measurement. The associated reference uncertainties are typically on the order of 2 µm to 3 µm. This program is very suitable for participants who measure machined work pieces using hand gages such as micrometers, calipers, height gages and indicators.

Show Details Inquire
KITS, Dimensional

Hand Tool Set

This ILC/PT Kit contains three dimensional hand tools. It is intended to provide a means for the participant to determine the appropriateness and effectiveness of the participant's practices, training, and measurement uncertainty relating to calibration of dimensional hand tools common to most inspection laboratories.

Participant is asked to perform a total of 12 measurements within the ranges of 0.00mm-30.00mm (Dial Indicator), 0.2500 in – 6.0000 in (Caliper), and 0.11300 in- 1.00000 in (Mitutoyo Micrometer).

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Hand Tool Set

This ILC/PT Kit contains three dimensional hand tools. It is intended to provide a means for the participant to determine the appropriateness and effectiveness of the participant's practices, training, and measurement uncertainty relating to calibration of dimensional hand tools common to most inspection laboratories.

Participant is asked to perform a total of 12 measurements within the ranges of 0.003 in-0.012 in (Dial Indicator), 1.5 in – 6 in (Caliper), and 1.21 in - 1.815 in (Mitutoyo Micrometer).

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire
KITS, Dimensional

Hand Tool Set

This ILC/PT Kit contains three dimensional hand tools. It is intended to provide a means for the participant to determine the appropriateness and effectiveness of the participant's practices, training, and measurement uncertainty relating to calibration of dimensional hand tools common to most inspection laboratories.

Participant is asked to perform a total of 12 measurements within the ranges of 2.54mm-14.00mm (Dial Indicator), 1.1140 in – 3.0000 in (Caliper), and 0.2445 in- 0.8500 in (Mitutoyo Micrometer).

Participants are expected to be familiar with, and have appropriate lab equipment and measurement uncertainties for calibration of similar devices.

Show Details Inquire

Theme picker

Copyright 2024 National Association for Proficiency Testing (NAPT)

Website developed by 10 Pound Gorilla

Contact Us Privacy & Terms